Product Feeding
The product in granular, crystalline, or powder form is fed into the fluidized bed dryer in a controlled and continuous manner via the feeding system.
Industrial Drying Systems
Fluid Bed Dryer
High-efficiency thermal drying and cooling systems.
Process-focused selection
Engineered based on product and site data
Material
Carbon steel, stainless steel, or a special coating
Capacity
Defined according to project capacity
Commissioning
Installation, operator handover, maintenance planning, and after-sales support are coordinated.
PROCESS EQUIPMENT
Process-oriented selection for Fluidized Bed Dryer Systems
MİYAY Fluidized Bed Dryer Systems are designed for controlled drying, cooling, or thermal treatment of products in granular, crystalline, and powder form. Thanks to high heat transfer efficiency, homogeneous temperature distribution, and precise process control, product quality is preserved while energy consumption is optimized. With static and vibrating design options, solutions suitable for different process requirements are offered.
- Fast and homogeneous drying with high heat and mass transfer
- Controlled and efficient drying with precise temperature control
- Flexible process design suitable for different product and particle characteristics
Why MİYAY?
- Process-oriented engineering approach
- Pilot and laboratory test support
- Thermal process expertise
- Manufacturing in compliance with CE standards
- Full automation solutions
- After-sales technical service and spare parts support
Solution Suited to Your Process
Each product has different drying characteristics. MİYAY designs and commissions the fluidized bed dryer system most suitable for your process through laboratory studies, pilot tests and detailed engineering services.
KEY FEATURES
Static and vibrating design options
High heat transfer efficiency
Homogeneous product temperature distribution
Low product loss and minimum thermal stress
Design suitable for drying, cooling, and reaction applications
Multi-zone temperature control
Energy recovery options
PLC / SCADA integration
ATEX and GMP compliant design options
Project-specific engineering solutions
Key Features and Advantages
Static or vibrating design options are offered together with high heat transfer efficiency and homogeneous product temperature distribution. Since the same bed can be designed for drying, cooling, and reaction applications, multi-zone temperature control and energy recovery are combined in a single system.
Optional equipment
- Multi-zone temperature control
- Integrated cooling zone
- Energy recovery system
- Dust collection system
- Cyclone and filter units
- ATEX-compliant design
- GMP-compliant design
- Remote access and SCADA integration
OPERATING PRINCIPLE
Working Principle and Process Steps of Fluidized Bed Dryer Systems
Fluidization
Heated process air is supplied homogeneously to the product bed through the distribution plate. Thanks to the air flow, the particles become fluidized and the entire product surface contacts the hot air.
Drying and Heat Transfer
The fluidized product is dried homogeneously through high-efficiency heat transfer. Depending on the process requirement, cooling or thermal treatment applications can also be carried out within the same system.
Product Discharge
The product that reaches the desired moisture content is discharged from the dryer in a controlled manner. Exhaust air and fine particles are removed by the filtration system, allowing the process to continue safely and continuously.
TECHNICAL SPECIFICATIONS
Technical data table for Fluidized Bed Dryer Systems
| Feature | Value |
|---|---|
| Equipment Type | Static or vibratory fluid bed dryer |
| Working Principle | Fluidized Bed |
| Product Type | Granular, crystalline, and powder products |
| Operating Temperature | Process Dependent |
| Heat Source | Natural gas, steam, thermal oil, electricity |
| Operating Pressure | Atmospheric or Controlled Pressure |
| Drying Zones | Single- or multi-zone |
| Cooling Zone | Optional |
| Energy Recovery | Optional |
| Automation | PLC / SCADA / DCS Compatible |
| Body Materials | Carbon Steel, AISI 304L, AISI 316L |
| Design Standard | CE, ATEX, GMP Optional |
Fluid Bed Dryer hakkında sık sorulan sorular
For which products is the fluidized bed dryer suitable?
It is suitable for granular, crystalline, and powder products. It operates on the fluidized bed principle with a static or vibrating fluidized bed design.
What heat sources can it operate with?
It can operate with natural gas, steam, thermal oil, or electricity. Drying can be single- or multi-zone; a cooling zone and energy recovery are optional.
What are the body material and design standard?
The body is manufactured from carbon steel, AISI 304L, or AISI 316L. The design standard is CE; ATEX and GMP are available as options, and automation is compatible with PLC/SCADA/DCS.
MODEL AND CAPACITY OPTIONS
FLUIDIZED BED DRYER SYSTEMS Model and Size Selection Table
| Model | Capacity | Quote |
|---|---|---|
| MPS-FBD-S | Static fluid bed dryer | Request a quote |
| MPS-FBD-V | Vibratory fluid bed dryer | Request a quote |
SPARE PARTS
Spare parts
Critical spare parts for operational continuity
01
MPS-SP-01
Air Distribution Plate (Air Distribution Plate)
02
MPS-SP-02
Distribution Nozzles (Air Nozzles)
03
MPS-SP-03
Fluidization Plates
04
MPS-SP-04
Vibration Motors (for Vibrating Models)
05
MPS-SP-05
Vibration Springs
06
MPS-SP-06
Eccentric Drive Mechanism
PRODUCT GALLERY
Equipment Details and Field Photos
1 / 2
REQUEST A QUOTE
REQUEST A QUOTE
Fluid Bed Dryer — Share your capacity and process requirements
Share your capacity, material, and process requirements so our engineering team can assess the right configuration.